Maytag Washer Error Codes: Meaning and How to Fix | Fixappliances CA (2024)

Maytag is renowned for manufacturing highly dependable washing machines, making it a top choice for consumers seeking reliability in their appliances. Their parts and electrical mechanics are intuitive and work well. Nonetheless, should the system detect any anomalies with your washing machine, you will likely get an error code that you may not know how to diagnose or deal with.

Maytag Washing Machine Error Codes: Description and Solution

Check the code explanations below for Maytag washing machine troubleshooting

Let’s talk in more detail.

drn: Washer is not draining properly

Condition:

The washer is not draining properly. This error code indicates that the washer basin may remain partially or completely filled with water.

Parts where possible failure may take place:

Water drain hose.

How to fix the problem yourself:

There are three different types of drain hose configurations on a top load washer that might need adjusting for fixing this Maytag washing machine error code:

1. Standpipe drain system. The terminal end of the drain pipe should be at least 36 inches and no more than 96 inches above the floor. Examine the installation site to confirm the ground level complies with the 36-inch requirement.
2. Laundry tub drain system. Similar to the standpipe system, the drain pipe end must be at least 36 inches and no more than 96 inches above the floor. Verify the installation point and ensure the ground level aligns with the 36-inch threshold.
3. Floor drain system. For a floor drain hose, a separately purchased siphon break kit is necessary. The siphon should be positioned at a minimum of 28 inches from the floor. Check the installation location and ensure the ground level meets the 28-inch threshold.

By adjusting the drain hose configuration according to these specifications, you can effectively resolve the Maytag washing machine error code issue. Remember to verify the compliance of the installation site with the specified requirements to ensure proper functioning of the washer.

F# E# or F##: System error code

Condition:

System error code.

Parts where possible failure may take place:

Computer motherboard or sensors.

How to fix the problem yourself:

To reset the motherboard code, press and hold the START/PAUSE button once to clear the code. Subsequently, press the START/PAUSE button again to reset the washer. If the code persists, it’s recommended to seek professional service for your Maytag washing machine error code.

HC Error Code: Reversed hot and cold inlet hoses

Condition:

Reversed hot and cold inlet hoses.

Parts where possible failure may take place:

Inlet hoses attachments to the water faucet and washing machine.

How to fix the problem yourself:

This is a fairly easy fix that requires switching the hose inlet hoses. The error message shows up when the hoses for hot and cold water are installed in the incorrect order. Reverse their positions and reset the motherboard by pressing and holding the START/PAUSE button twice.

LdL Error Code: Lid is not locked

Condition:

The door lid is not locked.

Parts where possible failure may take place:

Lid latch point, lid itself, or anywhere around the perimeter of the lid.

How to fix the problem yourself:

The LdL code means that the lid of your washer isn’t closed completely and locked. Fixing this issue requires checking the lid’s entire perimeter for any obstructions and removing them. Also, the lid locking latch might obstruct the point of contact with the washing machine body.

LdU Error Code: Lid cannot unlock

Condition:

The lid cannot unlock.

Parts where possible failure may take place:

Lid latch point, lid itself, or anywhere around the perimeter of the lid.

How to fix the problem yourself:

This code indicates that the washer lid is unable to lock. Removing a substantial item, such as a bulky blanket, from the top of the washer may alleviate the locking mechanism, enabling the washer to open without any hindrance.

LF, Lo FL or F8 E1: Washer is taking too long to fills

Condition:

The washing machine is taking an unusually long time to fill with water.

Parts where possible failure may take place:

The water supply inlet valve, water line, or other household faucets.

How to fix the problem yourself:

To troubleshoot a Maytag washing machine with this error code, check the water inlet valve and faucet where the water enters the washing machine. Check for kinks in the hoses leading to the washer if the valves are open and the faucet is turned on. Also, you must have hot and cold water supplied to the washer to fill properly.

Lid: Lid left open

Condition:

The lid is left open.

Parts where possible failure may take place:

The washer lid, locking mechanism, or the perimeter around the lid.

How to fix the problem yourself:

Ensure the washer lid is fully closed and level. The cycle will reset if the lid is left open for longer than ten minutes. This reset prompts the washer to drain, requiring you to restart the cycle. Don’t worry about adding more detergent. Start the cycle by pressing the START/PAUSE button once and closing the lid.

Ofb: Washer load out of balance

Condition:

The washer load is unbalanced.

Parts where possible failure may take place:

The internal washer drum.

How to fix the problem yourself:

When the washer is out of balance and running a load-balance correction routine, allow the washer to continue. Then, several measures can be taken to alleviate the issue.

A flashing dial means the water is stopped and you can open the lid. Move the clothing around more evenly at the bottom of the washer drum, close the lid, and press START/PAUSE once.

The vibrations during spinning are normal for an unbalanced load. Pause the load and redistribute the items evenly around the bottom of the washer drum.

Never add more water or soaked wet items to the washer cycle, as this tends to throw the cycle off balance.

The settings on the washer for large items should always be used, such as the Bulky/Sheets Deep Water Wash cycle for oversized things that don’t absorb water well.

OL: Washer load is too large

Condition:

The washer load is too large.

Parts where possible failure may take place:

The washer tub and clothing within.

How to fix the problem yourself:

This message indicates that the washer is overloaded. Remove some of the wet clothing from the washer and set it aside. Close the lid and press the START/PAUSE button once to restart the cycle. The code may reappear if there are still too many clothes in the washer.

PF: Power failure interrupted the cycle

Condition:

Power failure interrupted the washing cycle.

Parts where possible failure may take place:

Washing machine, motherboard.

How to fix the problem yourself:

Press and hold the START button to initiate a reset of the washing machine cycle.

Sud: Too many soap suds

Condition:

Excessive soap suds are present in the washer.

Parts where possible failure may take place:

Water inlet hose, washer basin, and the body of the washing machine.

How to fix the problem yourself:

Only use high-efficiency or HE standard washing machine detergent!

Take the clothing out of the cycle and run a RINSE/SPIN cycle to clear out the excessive soap suds.

LOC or LC: Control lock activated

Condition:

The control lock is activated.

Parts where possible failure may take place:

The locking mechanism on the lid.

How to fix the problem yourself:

Press and hold the CONTROL LOCK button. Some older models have a different button that is responsible for activating the control lock of the lid. Check your owner’s manual for which button this is.

dET: Detergent cartridge was not detected

Condition:

The detergent cartridge wasn’t detected in the dispenser.

Parts where possible failure may take place:

Detergent dispenser drawer.

How to fix the problem yourself:

Some models have detergent cartridge drawers where a detergent tablet is inserted before the washing load begins. Check if the tablet is in place, is inserted correctly, and the drawer is shut completely.

Int: Cycle paused, cancelled or interrupted

Condition:

The cycle was paused, cancelled, or interrupted.

Parts where possible failure may take place:

Motherboard: whole washing machine spin cycle.

How to fix the problem yourself:

Let the washer spin and drain completely, which may take up to 20 or 30 minutes. During this time, the code might be visible, which can be removed by pressing the PAUSE button twice and the POWER button once. If the code remains, do a manual power reset by unplugging and plugging back in the power cord to the washing machine.

rL or F34: Items detected during the clean washer cycle

Condition:

Items were detected in the washing machine during the clean-washer cycle.

Parts where possible failure may take place:

Washer drum.

How to fix the problem yourself:

It is one of the most common Maytag washing machine problems with an easy fix. Open the lid to the washer drum and remove any items during the clean washer cycle. Close the lid and press the START button to continue the cycle.

F5 E2: Washer door is not locking properly

Condition:

The washer door fails to lock and close properly.

Parts where possible failure may take place:

Washer lid, the perimeter of the lid.

How to fix the problem yourself:

This code necessitates straightforward troubleshooting for your Maytag washer. Ensure that the lid is not hindered and can close completely. Clear the code by pressing the PAUSE button twice and the POWER button once.

F7 E1: Motor speed sensor error

Condition:

Motor speed sensor error.

Parts where possible failure may take place:

Washer motor.

How to fix the problem yourself:

Given that this Maytag washing machine fault code points to an issue with the washer motor not reaching the proper speed, it can impede the cycle from running accurately.

To fix this issue:

1. Confirm that all shipping bolts have been removed.
2. Remove any excess items that may have overloaded the washer.

To clear the code, press the PAUSE button twice and the POWER button once.

F8 E2: Low flow of water sensed

Condition:

A low flow of water is sensed.

Parts where possible failure may take place:

Water inlet valve, faucet valve, or water inlet hoses.

How to fix the problem yourself:

There are several ways of checking the water flow into your washing machine. Go through this checklist before calling a professional:

1. The household water supply is activated.
2. Hot and cold water faucets are fully open.
3. No kinks are visible in the inlet hoses to the washing machine.
4. There are no anti-flood controls present on the waterline.

To clear the code, press the PAUSE button twice and the POWER button once.

F9 E1: Draining water takes too long

Condition:

Draining water is taking too long (usually more than eight minutes).

Parts where possible failure may take place:

Water drain hose, washer drum.

How to fix the problem yourself:

This is one of the trickier Maytag washer error codes. There are several aspects you need to check if your washer is not draining quickly enough.

1. Check for and straighten out any kinks in the hose.
2. Remove and check for clogs in the drain hose.
3. Adhere to standard standpipe requirements of being no more than 96 inches from the ground and 39 inches minimum from the ground.
4. Limit the use of soaps that cause excessive suds.

By tackling these potential issues and adhering to the suggested steps, you can effectively resolve the problem of slow water drainage in your Maytag washer. Taking proactive measures to maintain the functionality of your appliance will help prevent future occurrences of this error code.

Error Codes On a Maytag Washer: When I Need Repair Service

When you encounter error codes on your Maytag washer that you’re unable to resolve independently, it’s time to seek professional washer repair service. Here are some situations indicating the need for professional assistance:

1. Persistent Error Codes. If error codes persist despite your attempts to troubleshoot and resolve them using the manufacturer’s guidelines or online resources.
2. Complex Error Messages. Error codes that are accompanied by complex technical descriptions or require specialized diagnostic tools for interpretation.
3. Electrical or Mechanical Issues. Error codes indicating electrical or mechanical malfunctions within the washer’s components, such as the control board, motor, or sensors.
4. Repeated Malfunctions. If the washer experiences repeated malfunctions or error codes shortly after attempting DIY repairs or resets.
5. Safety Concerns. Error codes indicating potential safety hazards, such as electrical faults or water leakage, necessitating immediate professional attention.
6. Under Warranty. If your Maytag washer is still under warranty, contacting the manufacturer or an authorized repair service ensures compliance with warranty terms and avoids voiding the warranty through DIY repairs.
7. Lack of Expertise. When you lack the technical expertise, specialized tools, or diagnostic capabilities required to diagnose and repair complex issues.
8. Risk of Further Damage. Continuing to use the washer despite persistent error codes or malfunctions may risk further damage to the appliance or compromise its performance.

In such circumstances, enlisting the expertise of professional repair services from seasoned technicians guarantees precise diagnosis, efficient repairs, and the optimal performance of your Maytag washer. Professional Maytag repair service has the expertise, resources, and knowledge to address complex issues safely and efficiently, minimizing downtime and inconvenience.

Luckily, Fix Appliances CA has the knowledge and expertise of qualified appliance technicians to handle any Maytag washer error code.

If you need help with your Maytag washing machine error codes, make sure to give our team a call today at 888-242-0777. At Fix Appliances CA, our free service call helps you get peace of mind for all emergency situations that may take place. Call today!